View Full Version : Magnaflow Exhaust - Pics!
Muffler $110 (Online @ Performancepeddler.com cheapest you can get it)
Install $185 (Brackets $4 Pipes $44 Labor $137)
It's hanging from the stock rubber things btw
http://i12.photobucket.com/albums/a243/Gun5/Picture001.jpg
http://i12.photobucket.com/albums/a243/Gun5/Picture002.jpg
evan938
10-12-2005, 11:25 PM
i think you need to cut out some of the bumper and lift it up some. thats the ****ty thing about XDs is the rear bumper has no place to tuck an exhaust into
KeWLKaT
10-12-2005, 11:27 PM
what evan said.
looks nice though it would look better tucked in
what would they have todo to tuck it? take off the plastic and weld to frame? ya I think it looks pretty bad hanging down plus when I go up into a drive way (uphill) its only 2-3 inches from the ground. It will probably stay like this for a bit though
Mahonroy
10-12-2005, 11:30 PM
lol looks like the exact same muffler I have:
http://mahonroy.home.comcast.net/turbo/newp1.jpg
http://mahonroy.home.comcast.net/turbo/newp2.jpg
What diameter is your exhaust, and what do you think about the sound? Do you have cats still? Mine is 2.5 inch diameter with 1 high flow cat, thats all thats hooked up to my down pipe. I agree I would like to figure out a good way to cut my bumper and raise the exhaust up a little bit,
KeWLKaT
10-12-2005, 11:32 PM
mahonroy, nice stuff.
danm, i wonder how my 3'' piping will sound like :( lucky i have a bigass res on it :D
lol looks like the exact same muffler I have:
http://mahonroy.home.comcast.net/turbo/newp1.jpg
http://mahonroy.home.comcast.net/turbo/newp2.jpg
What diameter is your exhaust, and what do you think about the sound? Do you have cats still? Mine is 2.5 inch diameter with 1 high flow cat, thats all thats hooked up to my down pipe. I agree I would like to figure out a good way to cut my bumper and raise the exhaust up a little bit,
its 2.25" piping w/ 2.25" inlet on the muffler and the tip is 4".. and its cat back they took out something behind the cat which was pretty big I figured taht was the resonator? I know when I rev this ***** to 6-7 rpm's it shakes (doh) and some black smokes comes out wee :eek: would 2.5 or 3 been louder?
KeWLKaT
10-12-2005, 11:37 PM
yes it would have been louder. they say backpressure is good for n/a engines, but both me and mahonroy are talking about FI exhaust set-ups.
2.25'' piping is perfect for you. hows it sound?
yes it would have been louder. they say back pressure is good for n/a engines, but both me and mahonroy are talking about FI exhaust set-ups.
2.25'' piping is perfect for you. hows it sound?
sounds good @ 3-4 rpm's then at 5-6-7 I cant really hear it well inside at least I standed outside while my friend did it and **** its loud all the way from 2.. i'll have my intake on in a few days as well and my ground wire kit done so Im noticing a lot of performance diffs.. then Im going to reset the ecu (haven't so far) and get a huge boost rofl :eek:
in fact the guy who installed it was talking to me how most cars come out of there sounding like bumblebees on steroids and had never put a muffler like this on one of our cars and when he turned it on he said nope not bumblebee :D
Estopatitiana
10-12-2005, 11:48 PM
are these magnaflow mufflers straight through?
Elantra_GT_chic
10-13-2005, 12:03 AM
ooooo, can't wait to hear that baby in person, love. ;)
PRICE: $195.49
PART #: 14829
DESCRIPTION: Double Wall, Angle Cut
2.25" Inlet 4" Diam. Tip
7" Tip Length
5" x 8" Oval Body
14" Muffler Body Length
MAGAZINE ARTICLES: No Articles available
Additional Information
The Street Series is designed for the souped up street machine. It features a high flow tuning tube, balanced to the needs of the high revving import engine. The Street Series emits a smooth, deep tone while offering improved performance over OEM equipment. The Street Series is recommended for street cars with bolt-on performance modifications and custom body kits.
http://www.magnaflow.com/02product/mufflers/gifs/street02.jpg
theres the info on it.. looks straight to me
jfreak921
10-13-2005, 12:03 AM
are these magnaflow mufflers straight through?
Yes.
And to Gun5, do you have a header installed or are you running stock? What about CAI?
Yes.
And to Gun5, do you have a header installed or are you running stock? What about CAI?
CAI in 1-2 days (UPS) should be 2.5 piping or 2.75 and ground wire kit aswell is already half on (some wherent long enough)
evan938
10-13-2005, 12:37 AM
i have been thinking of switching to a muffler that looks a little less fart-pipe-ish, like that, but im not gonna pay for a new cat back, and i would HATE to cut up my EF exhaust. maybe, just maybe if i find an exhaust i like, ill get a couple pipes bent and a flange welded to go from the axle back, and if i dont like it, just unbolt it and put the old one back on
as for cutting the bumper, if its a 4" tip, find something thats about 4.5", hold it right against the bumper, w/ the bottom of the bumper being 1/2 way down the disc. (should look like this ----------------( )----- ) where the ( ) is whatever you find thats round, trace it out, and cut it. a dremmel will work, but the disc gets hot and will melt the plastic youre cutting, so maybe a jigsaw (if youre careful) would work better.
whatever you do, get it tucked in
i have been thinking of switching to a muffler that looks a little less fart-pipe-ish, like that, but im not gonna pay for a new cat back, and i would HATE to cut up my EF exhaust. maybe, just maybe if i find an exhaust i like, ill get a couple pipes bent and a flange welded to go from the axle back, and if i dont like it, just unbolt it and put the old one back on
as for cutting the bumper, if its a 4" tip, find something thats about 4.5", hold it right against the bumper, w/ the bottom of the bumper being 1/2 way down the disc. (should look like this ----------------( )----- ) where the ( ) is whatever you find thats round, trace it out, and cut it. a dremmel will work, but the disc gets hot and will melt the plastic youre cutting, so maybe a jigsaw (if youre careful) would work better.
whatever you do, get it tucked in
kinda confused, I get the find something 4.5 like something traced on a piece of paper maybe but after that im lost I know that the tip will be halfway in the bumper and the other will be hangin out still (how most are)
evan938
10-13-2005, 01:00 AM
you want something thats just a tad bigget than your tip so its got some room around it. hold it up to the bumper where the bottom wuold be 1/2 way down the circle, trace around the top, along the bumper, and cut along that line
you want something thats just a tad bigget than your tip so its got some room around it. hold it up to the bumper where the bottom wuold be 1/2 way down the circle, trace around the top, along the bumper, and cut along that line
yea needs alittle room when its moving sometimes from revvin high, Im going to use a magic marker to trace.. what to cut it with now (dont have a dremel, well battery is dead) and how the heck is the muffler shop going to raise the muffler, will they have to take those rubber things off and weld it higher I imagine
KeWLKaT
10-13-2005, 02:21 PM
no they will just shorten the "arms" on your muffler
no they will just shorten the "arms" on your muffler
oh ya n/m the metal pieces they put on the front/back of muffler got it
Cypher
10-13-2005, 02:36 PM
get a sound clip man!
get a sound clip man!
I dunno how to with my cam, its a Powershot Elph 500, E 500 or EL 500 (one of those by cannon.. I know it has the option we just dont have hte manual anymore
Cypher
10-13-2005, 05:34 PM
take a video instead it'll still pick up sound
Honestly, im not a big fan of those types of mufflers. I prefer the canister or something other then that. But it looks good! Glad to hear you like the sound, all the guys at the meet were amazed all I have is a CAI and magnaflow!
KeWLKaT
10-14-2005, 08:20 PM
opz are you coming to the big giant hyundaimeet? you'll get to hear my td04L there :D
knottravesty
10-14-2005, 08:42 PM
Yes please get some sort of sound clip... I wanna hear... it might be my next purchase lol...
opz are you coming to the big giant hyundaimeet? you'll get to hear my td04L there :D
Dunno yet...
knottravesty
10-20-2005, 11:36 AM
Any word on that exhaust Gun lol...
im going todo alittle movie soon, me doing crazy stuff in the car, showing off intake/exhaust/sound and my 5spokes ofcourse.. all safely done so jamie nothing to worry about :rolleyes:
Elantra_GT_chic
10-20-2005, 03:25 PM
im going todo alittle movie soon, me doing crazy stuff in the car, showing off intake/exhaust/sound and my 5spokes ofcourse.. all safely done so jamie nothing to worry about :rolleyes:
Hmmm, well I would believe that BUT....when you say that you're going to crazy stuff in the car, that just doesn't sound safe...especially when you're behind the wheel. I know you honey! :rolleyes:
Vampyrate
10-23-2005, 10:17 PM
well, those that ride together die together i guess... and besides a persons definition of "crazy" greatly varies, he might just be doing something tame compared to what i do to my car. i swear, i dog the hell out of the engine. im the only GLS that i know off that won't hesitate to try rallying in it as is.
though i am in the market for a new exhaust, im slowly getting away from that stock look and am just looking for just straight up power, but i need more input before i buy.
knottravesty
10-29-2005, 09:02 PM
RYAN!!!! I WANT A SOUND CLIP MAN... GET ON IT lol... i wanna buy this thing soon...
RYAN!!!! I WANT A SOUND CLIP MAN... GET ON IT lol... i wanna buy this thing soon...
arg bangs S500 powershot camera give me sound!
got some but i revd it to quick its like 9 PM and i cant make loud noises for long ill do it tomorrow during day.. and a drive by to
tricked03gls
10-30-2005, 06:32 AM
exhaust looks decent, not a big magnoflow fan but o well, so does anyone else got a raspy *** exhaust because of the header or the high flow cat?
Estopatitiana
10-31-2005, 12:55 AM
me..i have nothing but a header and a straight pipe bc my muffler deciced to fall apart...but yeah even when i had it it buzzed like piss
bolofly2003
06-01-2007, 01:46 PM
i want to put anpther mufflerin my elantra 2002 gls. i want two. i have a magnaflow and want to put another. waht need to do that. two muffler give more power?
lcanajoharie
06-01-2007, 02:02 PM
search and get ready for flaming. 1 muffler man... that's all.
Blackcasper2005
06-01-2007, 10:49 PM
if u want to do dual exhausts then i would probably do what i did and have just tips cause two mufflers doesnt like right, imo
DJ Hellfire
06-01-2007, 10:56 PM
what would they have todo to tuck it? take off the plastic and weld to frame? ya I think it looks pretty bad hanging down plus when I go up into a drive way (uphill) its only 2-3 inches from the ground. It will probably stay like this for a bit though
When I got mine done, I first made the cut out. Then I took it to Meineke and they just heated the hangers on the muffler and bent them up. Then they put shorter, stiffer rubber hanger thingies!
http://www.elantraxd.com/forums/showthread.php?t=18858&highlight=muffler+tucked
bdiggy
06-02-2007, 01:16 AM
When I got mine done, I first made the cut out. Then I took it to Meineke and they just heated the hangers on the muffler and bent them up. Then they put shorter, stiffer rubber hanger thingies!
http://www.elantraxd.com/forums/showthread.php?t=18858&highlight=muffler+tucked
I'm hoping that since this was from 10/05 that he already got the tuck job done. That and he hasn't been active since March,lol!
KeWLKaT
06-02-2007, 04:15 AM
Plus, he sold the car and bought a camaro/firebird or something of the sort, lol.
Plus, he sold the car and bought a camaro/firebird or something of the sort, lol.
:confused: I don't think I could ever bring myself to buy a camaro/firebird... ever. Just not my cup of tea.
vBulletin® v3.7.3, Copyright ©2000-2008, Jelsoft Enterprises Ltd.